How to do a parked regen Freightliner

Parked DPF Regen Light Flashing? (3 Minute Read)

Parked DPF regen light flashing?

This light only comeson when the truck is requesting a parked DPF regen. Every truck manufacturer designs this feature to appear when the soot level in the DPF filter reaches a certain level in order for the truck to keep operating.

What does this soot look like?

How to do a parked regen Freightliner

When your truck is requesting a parked DPF regen it means that the passive DPF regen your truck already went through was not enough to burn the soot in your DPF filter.

Do you actually need to do a parked DPF regen when the truck is asking for it?

The short answer is, Yes! If you keep driving your truck without doing a parked DPF regen your truck will enter a derated mode.

When this occurs your engine power and/or your speed will be limited.

What is an active DPF regen?

An active DPF regen is when the truck does this process automatically. This happens when the soot reaches a certain threshold and starts the active process to burn the soot off.You may notice your engine running harder when this is in"active mode"

There are so many causes for a failed active regen because it relies on conditions that need to be met in order for it to happen.

What happens if I cant perform the parked DPF regen when I try?

Well, this can happen when the activeregen failed for some reason.

If you fail a parked DPF regen you need to be aware that this will only lead to more issues and/or more derates if you continue driving. So be aware of what is going on so you can seek service as soon as possible.

How to do a parked regen Freightliner

How long does a parkedDPF regen take?

It takes approximately 20-60+ minutes.

It will continue to regen until the soot level has reached low or 0%. Some trucks will let you monitor your soot level gauge on the dashboard.

Whats the difference between parked DPF regen and forced DPF regen?

Parked DPF regen: Truck asks for DPF regen and you start the DPF regen by hitting a button on the dash.

Forced DPF Regen: A diagnostic scan tool at the dealer level will initiate a forced DPF regen. The conditions here do not have to bemet perfectly and they will force a regeneration to take place.

A forced DPF regen is done in order for the system to verify thatthe aftertreatmentsystem is ingood and working order. Ifyou can perform a forced DPF regenwithout any fault codesor issues appearing then the truck is ready to go!

Example: 2013 Volvo D13, has SPN 4094 FMI 1, MID 128 PSID 90 FMI 14. Dashboard lights up (DEF Quality being evaluated, 5mph temporary removed, continue driving).

How to do a parked regen Freightliner

The only way to clear this fault code is to make sure your DPF/SCR system is operating without any other faults. This fault will stay active until a service forced DPFregen is activated and the ECM/ACM runs through all the checks to make sure the NOx sensor values are within the required limits before it makes this fault code inactive.

So you can start a forced DPFregen even if you have DEF quality fault codes. The truck needs to run through all its checks to make sure the system is within the limits set by the manufacturer in order to clear the faults. This method is used on Volvos, Macks, Detroit diesel, and other manufacturers as well.

A forced DPFregen will ensure that the DPF / SCR System is clean from any soot buildup. If you make sure to do this more than just once it may help your DPF system last longer. We recommend running a service DPF regeneration once a month. You may see better MPG because your filters are cleaned out and moving air more efficiently through your exhaust.

OTR Performance providesyou with atool that will allow you to start a forced regeneration.The OTR reset tool will allow you to do this within 30 seconds - 4 minutes. We also provide an app OTR diagnostics where you can perform advanced diagnostic commands, such as a forced DPF regen from your mobile device or a tablet. OTR diagnostics also allows you to read and reset your fault codes, view live data, and so much more. Check it out here.

Heres how to use the OTR reset tool:

  1. Start the engine, make sure its at operating temperature.
  2. Make sure PTO off, parking brake applied, and the clutch is not engaged.
  3. Plug in the OTR reset tool into the diagnostic port. *set a timer*
  4. Wait for the regeneration to start.
  5. Monitor the Exhaust temperature and RPM.
  6. When the idle comes back down it means that the regen has finished.
  7. If the regen starts and stops then you may have a problem that prevents the regen from taking place. Check for faults and try again.

I hope this helps with some questions that seem to come up!

Untilnext time!
Stay safe, stay healthy & be blessed

Looking to learn more?Check out our other blog posts.

  • How long should a forced DPF regeneration last?
  • Tell-tale symptoms of a successful (or unsuccessful) forced DPF regeneration.
  • What is face plugging? How does it happen? How can I fix it?
  • What happens if your truck can no longer regen?
  • What is Forced DPF Regen?
  • Common DPF questions Answered!
  • What does poor DEF quality Mean?

OTR diagnostics allows you to read and reset fault codes, view live data, and run advanced diagnostic functions, including forced DPF regen with your mobile phone or tablet. Select which engine you have for your diagnostic package.

  • Cummins ISX, ISB, ISC, ISL, X15, X12 Engines
  • Detroit Diesel S60, DD60, DD13, DD15, DD16 Engines
  • Paccar MX11, MX13 Engines
  • Paccar PX6, PX7, PX8, PX9Engines
  • VolvoD11, D13, D16 Engines
  • Mack MP7, MP8, M10 Engines
  • Professional (All-in-One) Engines

TheOTR reset tool is specific to which model and engine you have. Select which engine for more specific details.

  • Volvo D11, D13, D16 Engines
  • Mack MP7, MP8, MP10 Engines
  • Cummins ISB, ISL, ISX Engines
  • Paccar MX11, MX13 Engines
  • Paccar PX6, PX7, PX8, PX9 Engines
  • Detroit Diesel S60, DD13, DD15, DD16 Engines
  • International Maxxforce 11/13 N13 N9 N10 Engines
Share Share on Facebook Tweet Tweet on Twitter

Leave us your question

Phone Number Message

How to do a parked regen Freightliner
How to do a parked regen Freightliner
What are Truck Fault Codes? Everything You Need to Know

Continue reading

How to do a parked regen Freightliner
How to do a parked regen Freightliner
What is an aftertreatment system? (...and why should I care?)

Continue reading

How to do a parked regen Freightliner
How to do a parked regen Freightliner
PACCAR MX Engine Diagnostic Tools Explained Davie 4 and OTRdiagnostics

Continue reading

View all